21
Product
1
21
7
Draining the engine oil on Type 1 engines was previously done from the bottom of the engine block. On Type 1 engines with 25-30 hp, this was done by removing the oil pan plate, which also held the oil filter in place. On 1200, 1300, 1500 and 1600 cc engines, there is often a drain plug that can be unscrewed to drain the oil from the engine block without having to remove the plate. These plates have long been available as part of the complete oil change kit No: 1852 12/13 for 1600 and No: 1852...
In stock
Bruttó ár: 4 990 Ft / db
Bruttó ár: 5 390 Ft / db
46
Oil pump cover, EMPI (rimless)
1805-01EMPI
The corresponding screws are 1805-500. The gasket is 1805-02 or 1805-03.
In stock
Bruttó ár: 3 710 Ft / db
Bruttó ár: 6 930 Ft / db
NEW
Available to order
Bruttó ár: 11 750 Ft / db
NEW
VW Type 1 1.2-1.6 08/59-12/86 VW Transporter T1 1.2-1.5 08/59-07/67 VW Transporter T2 1.6 08/67-07/79 VW Karmann Ghia 1.2-1.6 08/59-07/74 VW Type 3 1.5-1.6 04/61-07/73 VW Transporter T4 1.9-2.8 (incl. D) 01/96-04/03 VW 181 1.5-1.6 09/69-02/79 VW Transporter T3 1.6 05/79-12/82
In stock
Bruttó ár: 1 690 Ft / db
NEW
Draining the engine oil on Type 1 engines was previously done from the bottom of the engine case. On Type 1 engines with 25-30 hp, this was done by removing the oil pan plate that also held the oil filter in place. On 1200, 1300, 1500 and 1600 cc engines, there is often a drain plug that can be unscrewed to drain the oil from the engine block without having to remove the plate. These drain covers have long been available as part of the complete oil change kit # 1852 12/13 for 1600 and # 1852-...
In stock
Bruttó ár: 5 140 Ft / db
Available to order
Bruttó ár: 126 160 Ft / db
For all Type 1 engines. 1200-1300-1500-1600ccm
In stock
Bruttó ár: 10 810 Ft / db
From August 1969, the oil channels in the crankcase were widened from 8 to 10 mm, and at the same time the oil cooler openings. So, in order to be able to mount the new 10 mm oil cooler on an 8 mm crankcase, VW developed this adapter set. Of course, an old 8 mm cooler can also be mounted on a 10 mm crankcase the other way around. To do this, you need to use 3 washers located between the cooler and the crankcase.
In stock
Bruttó ár: 1 170 Ft / db
In stock
Bruttó ár: 23 340 Ft / db
1851 the paper gasket set, with the copper snap rings. 1853 the oil-settlement grate,
In stock
Bruttó ár: 8 510 Ft / db
With this stainless steel oil pan plate for Type-1 engines, you can replace corroded or deformed original elements. The original oil pan plate can deform when driving over traffic islands, touching curbs and ramps, or when the nuts are tightened too much. All these problems are a thing of the past with Vintage Speeds RVS oil pan plates and you can avoid the high costs of oil leaks. Each one is available from stock with 2 gaskets and mounting nuts. The oil pan plug is available separately unde...
Available to order
Bruttó ár: 28 120 Ft / db
8mm stud bolt, Alu; with 26mm gear; for 3-rivet driveshaft; large oil hole
In stock
Bruttó ár: 23 430 Ft / db
Oil pump cover, original
1805-01
The corresponding screws are 1805-500. The gasket is 1805-02 or 1805-03. The gasket under the cover is 1805-400.
In stock
Bruttó ár: 5 140 Ft / db
Between 0.3 - 0.6 Bar, used on Beetles, T1Buses, Karmann and Brazil buses manufactured until 1960.
In stock
Bruttó ár: 5 640 Ft / db
Available to order
Bruttó ár: 47 990 Ft / db
21
Product
1
21