132
Product
91
120
Classic Line quality
VW Transporter T1 1.5 11/62-07/67
VW Transporter T2 1.6 08/67-07/71
Exhaust kit at the rear, with one exhaust pipe and mounting kit, factory type. Made of gray painted steel. TÜV/EEC approved.
VW Transporter T1 1.5 11/62-07/67
VW Transporter T2 1.6 08/67-07/71
Exhaust kit at the rear, with one exhaust pipe and mounting kit, factory type. Made of gray painted steel. TÜV/EEC approved.
In stock
Bruttó ár: 74 900 Ft / db
Available to order
Bruttó ár: 112 460 Ft / db
Available to order
Bruttó ár: 99 060 Ft / db
The nuts on Type 4 mufflers are often too tight or the nuts are too bad to loosen properly. This makes it very difficult to replace the heat exchanger or muffler. This kit includes 6 new studs with matching nuts and 2 new gaskets. Everything you need to get your exhaust connected.
Available to order
Bruttó ár: 11 750 Ft / db
Available to order
Bruttó ár: 2 340 Ft / db
Use this set for the 1060-01 and 1060-01-ECO mufflers.
In stock
Bruttó ár: 7 230 Ft / készlet
Available to order
Bruttó ár: 79 480 Ft / db
Available to order
Bruttó ár: 70 090 Ft / db
Available to order
Bruttó ár: 135 500 Ft / db
VW Transporter T1 1.5 01/63-07/67 VW Transporter T2 1.6 08/67-07/71 The fitting kit for it is 1001-20. Or you can complete it with the following, 1061, 1062, 1063, 1065, you can definitely put it together, choose the right one for it. Classic Line quality, ECO version. The set includes the 1060-5 or 1060-6 kit!
In stock
Bruttó ár: 41 310 Ft / db
In stock
Bruttó ár: 98 120 Ft / db
Header 4 in 1 (with 35mm inner diameter)
In stock
Bruttó ár: 64 990 Ft / db
Available to order
Bruttó ár: 131 760 Ft / db
Type 1 1.3-1.6 08/65-07/73
Transporter T1 1.5 08/62-07/67
Transporter T2 1.6 08/67-07/70
Karmann Ghia 1.3-1.6 08/65-07/73
Transporter T1 1.5 08/62-07/67
Transporter T2 1.6 08/67-07/70
Karmann Ghia 1.3-1.6 08/65-07/73
Available to order
Bruttó ár: 103 230 Ft / db
Support bracket for T2 buses to support the end of the exhaust pipe coming out of the muffler and keep it stable and free from vibration. Without this, the pipe can easily break.
In stock
Bruttó ár: 4 910 Ft / db
These seals can withstand temperatures up to 1200°C and are located under the inspection cover on Type4 models at the transition between the heat exchanger and the cooling housing. When disassembling the heat exchangers or the cooling housing, these covers must be removed and the seals are often lost in the process. Without these seals, the air blown into the heat exchangers cannot be properly sealed.
Available to order
Bruttó ár: 7 050 Ft / db
These seals can withstand temperatures up to 1200°C and are located under the inspection cover on Type4 models at the transition between the heat exchanger and the cooling housing. When disassembling the heat exchangers or the cooling housing, these covers must be removed and the seals are often lost in the process. Without these seals, the air blown into the heat exchangers cannot be properly sealed.
Available to order
Bruttó ár: 7 050 Ft / db
This is the connecting pipe that is clamped to the top of the exhaust and runs through the rear engine case (left and right of the crankshaft pulley). The air hose (BBT 1095 or 1095-1) connects to this at the top and draws air from the fan shroud through the exhaust into the heat exchanger, then carries the warm air forward. Bob developed this after he damaged an original hose with sharp edges and made it with a tapered top and bottom so the cardboard heater hose would slide through and be ea...
In stock
Bruttó ár: 1 640 Ft / db
132
Product
91
120