139
Product
91
120
Ball head, 1303, 08/73- (37.6mm)
1334-01
Ball head with base for the 1303 running gear after August 1973, for the version with screw fastening on both sides. (37.6mm socket)
In stock
Bruttó ár: 4 850 Ft / db
Ball joint lower, modified to allow greater suspension movement when cars are lowered or lifted.
In stock
Bruttó ár: 14 920 Ft / db
Ball joint upper, modified to allow greater suspension movement when cars are lowered or raised.
In stock
Bruttó ár: 14 920 Ft / db
Rubber bushing for the front stabilizer on the chassis head. The mounting clamp is 1354-100 and the mounting screws are 1354-150.
In stock
Bruttó ár: 1 410 Ft / db
Available to order
Bruttó ár: 8 900 Ft / db
The package contains parts with serial numbers 311 405 625 + 311 405 645 + 131 405 641A.
The bearings can also be purchased separately, namely the inner bearing is 1356-110 and the outer is 1356-210 and 1363-010 (for disc brakes) or 1364-010 (for drum brakes). The washer that secures the bearing is 1360.
The bearings can also be purchased separately, namely the inner bearing is 1356-110 and the outer is 1356-210 and 1363-010 (for disc brakes) or 1364-010 (for drum brakes). The washer that secures the bearing is 1360.
In stock
Bruttó ár: 8 880 Ft / db
Beetle from 08/67 for front wheel Karmann Ghia from 08/67 for front wheel Type 3 from 08/67 for front wheel VW Golf/Jetta 1.1-1.8 (incl. D) 02/74-02/84 for rear wheel VW Golf Cabrio 1.5-1.8 01/79-04/93 for rear wheel
In stock
Bruttó ár: 2 990 Ft / db
NOS (new old stock) Beetle 08/65- Karmann Ghia 08/65- Type 181
Available to order
Bruttó ár: 2 115 Ft / db
These bushings are turned parallel on the outside and conical on the inside. When you have drilled the connecting rod hole in the spindle to the indicated diameter, you can install the bushings (pay attention to the tension) and place the connecting rod upside down. Prevents the connecting rods from touching the fuel tank housing on heavily lowered vehicles! Sold with assembly instructions in English!
In stock
Bruttó ár: 19 680 Ft / készlet
In stock
Bruttó ár: 1 410 Ft / db
The corresponding locking nut is 1396-91.
In stock
Bruttó ár: 2 340 Ft / db
Shock absorber bushing for the eyelet part, but can also be used for the upper half of the vertical rod of the rear stabilizer. It needs to be shaped, but someone has already solved it. Since this cannot be found on the market for the same price. Dimensions: outer diameter: 30mm inner diameter: 10-11mm width: 21mm the inner distance between the two edges is 17mm
In stock
Bruttó ár: 1 110 Ft / db
In stock
Bruttó ár: 4 940 Ft / szett
The purpose of these grease seals is to seal the connection between the Beetle and Karmann Ghia control arms and the front axle until 08/65, so that the lubricating grease remains on the front axle and sand and moisture cannot penetrate the front axle housing. The latter has quite destructive consequences on the running surfaces of the front axle bearing and control arm, so cracked, hardened ones must be replaced immediately
In stock
Bruttó ár: 3 280 Ft / szett
In stock
Bruttó ár: 3 280 Ft / pár
In stock
Bruttó ár: 1 400 Ft / db
Available to order
Bruttó ár: 124 240 Ft / szett
In stock
Bruttó ár: 24 420 Ft / szett
In stock
Bruttó ár: 2 110 Ft / készlet
In stock
Bruttó ár: 2 110 Ft / készlet
Stainless steel clamp kit and urethane levels for connecting the front wishbone to the stabilizer. Easy to install version.
In stock
Bruttó ár: 29 575 Ft / készlet
Our sway bar mounting kits are manufactured from high quality 2mm steel, exactly like the original, for a perfect fit and your safety. Beware of cheap or poorly fitting reproductions! For models with pivot pins.
In stock
Bruttó ár: 9 260 Ft / készlet
Inner bushing in the rear control arm, chassis side (Front axle)
In stock
Bruttó ár: 2 350 Ft / db
In stock
Bruttó ár: 2 570 Ft / db
139
Product
91
120